Dynemix India Engineering Pvt. Ltd. is trusted and reliable Manufacturer and Exporter of Sludge Conveying System in Belarus.
Our Manufacturing unit Is based in Ahmedabad, Gujarat, India.
Dynemix India Engineering Pvt. Ltd. offers sludge conveying solutions tailored to Belarusian conditions: cold climates, seasonal temperature swings, variable sludge consistency, and regulatory requirements for odour control, low emissions, and reliability.
Whether for municipal sewage works, food & beverage, pulp & paper, or industrial wastewater, our systems ensure efficient, clean, low‑maintenance sludge transport.
Features of Dynemix Sludge Conveying System
- Corrosion‑resistant materials: use of stainless steel or coated carbon steel to withstand corrosive components in sludge.
- Enclosed, sealed design: to prevent leaks, odours, dust or environmental contamination.
- Low clogging / non‑clogging or shaftless screw or plug design: especially for viscous, fibrous or sticky sludge.
- Flexible layout: ability to handle horizontal, inclined, or vertical conveying; modular design to integrate with existing equipment (filter presses, centrifuges, dewatering units).
- Variable capacity and throughput: designed to handle small to large sludge volumes (customisable).
- Energy efficient drive and motor system: optimised to reduce power consumption, especially relevant in colder climates where auxiliary heating or frost prevention may consume extra power.
- Low noise, low emissions: enclosed systems reduce odour and fugitive dust; acoustic insulation if required.
- Robust, easy maintenance: minimal moving parts, accessible service points, durable wear components.
- Control & automation ready: options for SCADA integration, sensors for flow, moisture, temperature, blockage detection.
Work Principle of Sludge Conveying System
Below is a general working principle. Specific design (screw, pneumatic, belt conveyors etc.) may vary depending on the sludge type, consistency, and site layout.
- Sludge Collection / Pre‑Treatment
Sludge is collected from dewatering units (filter presses, centrifuges, belt presses), or from sludge storage/digestion tanks. Pre‑treatment may include thickening, screening to remove large solids, or partial dewatering to reduce volume. - Feed Inlet / Hopper
The sludge enters the conveying system via a feed hopper or inlet port. The hopper may include agitation or mixing to ensure uniform feed and avoid blockages. - Conveying Mechanism
- In a shaftless screw conveyor: a flexible spiral screw rotates inside a trough, pushing sludge forward. Absence of a central shaft reduces clogging because sludge cannot build around a shaft.
- In belt conveyors: sludge cake or thickened sludge is placed on a belt and carried; for wet sludge, enclosed or trough‑type belt conveyors may be used.
- In pneumatic / dense‑phase systems: slurry or sludge particles are transported via air or gas flow through sealed pipelines. Dense‑phase systems use intermittent plugs of material pushed through the line, maintaining material integrity and reducing wear.
- In vertical/horizontal screw combinations: to lift sludge to higher elevation or feed equipment located above ground level.
- Discharge / Destination
After transport, sludge may be delivered to:- sludge drying beds
- incineration units
- composting or fertilizer applications (if safe)
- landfill or disposal units
- post‑treatment (e.g. further dewatering or stabilization)
- Control & Monitoring
Throughout the system: sensors monitor flow rate, moisture content, pressure drop (for pneumatic), motor load; automated controls to avoid overload or blockage, ensure smooth operation.
Uses / Applications
Typical applications of sludge conveying systems include:
- Municipal wastewater treatment plants (transporting sludge from dewatering to disposal or reuse)
- Industrial wastewater plants (food processing, pulp & paper, textiles, chemicals)
- Sewage sludge handling in rural or remote areas in Belarus
- Treatment plants in cold regions where sludge may freeze or become more viscous
- Sludge incineration or drying operations
- Composting, fertilizer production using treated sludge
- Operations requiring vertical lifting of sludge to feed higher level equipment
Dynemix India Engineering Pvt. Ltd. is Exporter of Sludge Conveying System in Belarus including location in Minsk, Homyel’, Vitsyebsk, Hrodna, Mahilyow, Brest, Babruysk, Baranavichy, Horad Barysaw, Pinsk, Mazyr, Lida, Orsha, Salihorsk, Navapolatsk, Maladzyechna, Polatsk, Zhlobin, Rechytsa, Horad Zhodzina, Svyetlahorsk, Slutsk, Kobryn, Slonim, Vawkavysk, Kalinkavichy, Smarhon, Rahachow, Dzyarzhynsk, Asipovichy, Horki, Byaroza, Navahrudak, Vilyeyka, Luninyets, Krychaw, Ivatsevichy, Horad Smalyavichy, Mar’’ina Horka, Pruzhany, Pastavy, Dobrush, Fanipal’, Hlybokaye, Stowbtsy, Zaslawye, Lyepyel, Ashmyany, Bykhaw, Ivanava, Zhytkavichy, Nyasvizh, Shchuchyn, Lahoysk, Klimavichy, Kastsyukovichy, Shklow, Drahichyn, Astravyets, Masty, Zhabinka, Stolin, Hantsavichy, Khoyniki, Malaryta, Mikashevichy, Lyelchytsy, Novalukoml’, Haradok, Byerazino, Lyuban, Klyetsk, Byelaazyorsk, Staryya Darohi, Uzda, Lyakhavichy, Chervyen, Machulishchy, Pyetrykaw, Baran, Kapyl, Valozhyn, Mstsislaw, Chavusy, Byalynichy, Skidal’, Talachyn and many more.
For more information or to request a quote, please contact us.
Website: www.dynemix.com
Phone No: +91 9909136200 | +91 9904136900
Email Id: inquiry@dynemix.com
View Product: Click here
